<nobr id="9nz9n"></nobr>

<em id="9nz9n"><form id="9nz9n"></form></em><meter id="9nz9n"><ruby id="9nz9n"><mark id="9nz9n"></mark></ruby></meter>

<b id="9nz9n"></b>

    <rp id="9nz9n"><ruby id="9nz9n"><delect id="9nz9n"></delect></ruby></rp>

      <form id="9nz9n"><address id="9nz9n"></address></form>
          <dfn id="9nz9n"></dfn>
            <font id="9nz9n"><var id="9nz9n"><del id="9nz9n"></del></var></font>

            <sub id="9nz9n"></sub>

            華陽玻璃清洗機

            專注高壓釜、玻璃清洗機及熱彎爐等產品二十多年

            張經理

            13961473534

            高壓釜出口

            日期:2020-01-04 10:55:02

              CONVECTIONAL

            GLASS AUTOCLAVE
             高壓釜出口
            Changzhou HUAYANG Glass Equipment CO., LTD
             Tel:+86-519-88237372Email: 64950300@qq.com
            1. Brief Introduction
             The assembling of two or more glass sheets with a kind of laminated plastic film interposed between them, after being adequately treatment in autoclave, is called SAFETY LAMINATED GLASS.. Of large use, and more and more requested by the market by virtue of the more restrictive norms in subjects like stoutness and security are tempered glass, both flat and curved, up to break-through proof and bullet-proof glasses. Therefore, it can be easily understood how the kind of assembling of laminated plastic (PVB) and above all the polymerization treatment inside the autoclave are of essential importance to obtain a product with good quality.
            高壓釜出口2
             In fact, the role of Flourish autoclaves is to obtain the desired quality of the product. The reliability and the precision of the cycles in autoclave allows to reach and keep high quality standards of the product.
            2. Basic Data
            2-1. Model and Size of the Convectional Glass Autoclave
            Definition Diameter of the autoclave. Effective length is to point to do the actual length of the glass.
            2-1-1   Autoclave ModelGYF-3075    Diameter: 3000mm   Effective length: 7500mm
            2-2. Production Performance
            2-2-1   Product size: max. 2440mm x3660mm
            2-2-2   Product thickness: 2.8mm ~ 80mm
            2-3. Production capacity (Automobile industry):
            2-3-1   Working circle of autoclave: 3.5~5hours, 2circle/10h.
            2-3-2   Max Capacity of autoclave: about 250 pcs. of laminated glass per circle (as 2.5G +0.76 PVB +2.5G, Glass size of the windshield: 1500mmX1000mm)
            2-4. Electric Power:
            2-4-1   Power supply: 400VAC, 3P+N+PE, 50/60Hz, >= 200KVA
            2-4-2   Total power:     182 kw (including air compressor system)
            The power of autoclave is 130kw, Compressor system:55 KW, Other auxiliary equipments about 8KW.
            2-5. Water and Air supply:
            2-5-1 Water supply: 0.5cbm/min, pressure >=3kgf/sqm
            2-5-2   Air source for Autoclave:    1.3Mpa   Air Source for other equipment: 0.6 - 0.8 MPa
            2-6 Area of the Autoclave
            Total length: appro.11000mm
            Total width about 6000mm
            <See the Foundation Drawing of Glass autoclave GYF-3075>3. Equipment List and price
            3.1 The main equipments :
            Item
            Description of equipment
            Qty.
            Unit Price(RMB)
            001
             Glass Autoclave (Ф3m*7.5m,Chinese Pressure vessel standard)
            Including electrical cabinet and control system, Export standard
            Transport to the port of Shanghai
            Including tax and freight
            1set
            RMB 370000
            002
            Glass Autoclave (Ф3m*7.5mEuropean Security Certification)
            Including electrical cabinet and control system, Export standard
            Transport to the port of Shanghai
            Including tax and freight
            1set
            RMB 380000
             
             
            3.2 Peripheral equipmentsOptional:
            4General feature and working process of the glass autoclave
            4-1General feature
            FLOURISHGlass Autoclave is suitable for manufacturing various laminated glasssuch as windscreen, bullet-proof glass,anti-bombing glass, and so on. It also can guarantee the perfect product quality and high performance,in which temperature, pressure and vacuum can be controlled effectively. It can get the best temperature and pressure for manufacturing laminated glass with various technique requirements through a full set of specially designed inner convection circulation devices combining with power adjustable heating systempressure controlling elements and efficient cooling unit.
            The whole operation process ofFLOURISH Glass Autoclave for windscreen has 5 segments. Pre-heating and pre-pressing segment,heating and pressurizing segment, temperature and pressure holding segment, cooling segment and air exhaust segment. During the whole process, temperature and pressure in all segments will be monitored by HIM or PC, and the operation process will be realized by our exclusively developed TPCThermal Processing Controlsoftware which is based on PLC control system to ensure the full automatic operation.
             
            4-2Working process of convectional glass autoclave
            高壓釜出口3 
             
            5. Equipment Details
            5-1GeneraStructure
             高壓釜出口4
            5-2Pressure vessel
            Pressure vessel with quick-opening door, certified to Chinese Pressure Vessel Code. The certificate is GB150-2011Steel Pressure Vessel 
            5-3Quick Closing Doors
            Ø         The whole system consists of four parts: a pair of gear flange, driven devices and sealring.
            Ø         Hydraulicoperated door openingclosing and locking. It is controlled by PLC system.
            Ø         The seal ring is made of silicon rubber, high temperature resistance.
            Ø          
            高壓釜出口5.jpg 高壓釜出口6.jpg
             
            It can be manual operated by the switches on the electrical cabinet near the door also.
            5-4. Insulation System
            Ø         Insulationinner insulation
            Ø         Insulation materialaluminium silicaterock wool
            Ø         Internal sheet metal: stainless steel,0.8mm
            Ø         Insulation thickness80mm
            高壓釜出口7.jpg 高壓釜出口8.jpg
            5-5. Floor supports and rails
            Ø         Rail loading:10,000kg,Increased loading can be offered optionally.
            Ø         Rail type:unequal angle steel
            Ø         Floor loading:400kg,Increased loading can be offered optionally.
            Ø         Form of floor supports Mild Steel Checkered Plate
            5-6. Heating System
            Ø         The heating system consists of the main heating zone and auxiliary heating zone, the heating element located in the rear to ensure uniformity of temperature during the heating process.
            5-7. Pressure components
            Ø         Inlet and exhaust valve:3-piece ball valve.
            Ø         Manual exhaust valve:3-piece ball valve.
            Ø         Pressure transducer: 1
            ?Accuracy: +/- 20mbar
                                               Includes HMI monitoring, data-acquisition, and control
             
            5-8. Cooling system heating exchange
            Ø         The main heating exchanger is made ofAluminum finned tube, which located in the rear of the autoclave.
            Ø         Exchanger mounted on a transport trolley for easy system maintenance.
            Ø         In this phase the laminated glass is made cold.
            5-9. Forced convection system
            Ø         Hot air channel
            This glass autoclave is different from the conventional autoclaves. It has a U type duct that is used to transfer hot air from the rear of the autoclave to the front. This unique design features make the temperature more uniform.
            高壓釜出口9.jpg 高壓釜出口10.jpg
             
            Ø         The Motor fan for circulation
            The motor is bolted to the body of the autoclave, it drives the fan directly, andthey are connected by a pair of couplings, without belts.(see the picture)
             
            Ø         Main parameters of circulating motor fan
            Power15KW,
            Connecting formatdirect-connected
            Rotate speed960r/min(400V/50HZ
            Fan wheel6#centrifugal impeller,
            Wind pressure980Pa,
            Flow9900M3/h.
            Ø         Shaft sealing and cooling
            Mechanical seal ,silicon carbide - graphite materials as static and dynamic ring seal , bearings with high-temperature series .
            Working, use of water cooling, to guarantee a minimum service life of more than 8000 hours, the shaft water cooling with separate water pump and flow switch to be fitted to monitor water flow and automatically alarm/stop the cycle if there is not enough water flow.
            5-10. Temperature monitoring components
            Ø         Air temperature thermocouples: 2
            PT100, including HMI monitoring,data-acquisition, and control
            Ø         Hi-limit thermocouple 1
             PT100, including HMI monitoring/control.
            5-11. Vacuum system
            Ø         Vacuum source ports: 6 total
            Ø         Each source port will include:
            ½"internal thread pipe joint
            External manual blocking valve, stainless-steel
            Ø         Vacuum transducer ports: 1 total
            Customer can manufacture bent and strange shape laminated glass by the vacuum system. But it is suitable for the condition that the quantity of the glass is not too much.
            5-12. Control System
            Ø         Control System is developed based on the research and development toward glass processing industry, including the PLC central controlling part, touch screen (HIM) operation system and network. The operation of the whole system is based on the exclusive developedTPC Thermal Processing Control software.
            Ø         It can insert or save the production technique process, display the pressure and temperature curve anytime; and its paperless record function can realize record, save and check of technique curve and process parameters.
            Ø         Advanced TPC control software makes the controlling technique during the process of temperature waiting for pressure, pressure waiting for temperature possible to ensure the simultaneous effect of temperature and pressure according to the settled technique curve, and it also has over-temperature and overpressure alarm and various safety protection functions.
            高壓釜出口11.jpg
            Full automatic operation control and monitor run status information, data saving information, integrity check information and run override controls
            高壓釜出口12.jpg
            Manual operation screen allows operator take manual control temperature, pressure, vacuum, fan, and valves as allowed.
            高壓釜出口13.jpg 高壓釜出口14.jpg

            5-13. Safety systems

            Ø         Mechanical and electrical interlocks for door closure,the autoclave can not be opened when pressure in the autoclave higher than air pressure。
            Ø         It will auto-alarm when facing over-temperature or over-pressure; meanwhile, it will drop the temperature down and release the air automatically.
            Ø         One Pressure safety relief valve to protect the autoclave.
            5-14. Paint
            FLOURISH Glass autoclave will be primed and painted high-gloss "Blue " color. Customer
            requested color can be quoted optionally.
             6Main technical data of autoclave
            GYF-3075 GLASS AUTOCLAVE TECHNICAL PARAMETER
            No.
            Description
            Unit
            Specifications and Parameters
            1
            Inner Diameter
            mm
            3000
            2
            Working Length
            mm
            7500
            3
            Max. Glass Size
            mm
            2440X3660
            4
            Autoclave Track Distance
            mm
            800
            5
            Track height
            mm
            480
            6
            Design Pressure
            Mpa
            1.5
            7
            Design Temperature
            160
            8
            Working Pressure
            Mpa
            1.3
            9
            Working Temperature
            150
            10
            Safety valve exhaust
            Mpa
            1.4
            11
            Working Medium
            ---- 
            Compressed Air
            12
            Heating Mode
            ---- 
            ElectricConvection+Radiation 
            17
            Heater
            ---- 
            inconel tubular heaters
            18
            Heating Power
            KW
            130
            19
            Circulating Fan Motor power
            KW
            15
            20
            Thermocouple type
            --- 
            PT100
            21
            Air Temperature Thermocouples
            Piece
            1
            23
            Pressure Transducer
            Piece
            1
            24
            Vaccum Lines
            Piece
            ---- 
            25
            Control Mode
            --- 
            PLC+PC
            26
            Control Software
            --- 
             Thermal Processing Control (TPC)
            23
            Insulation
            --- 
            Internal
            24
            Supporting air tank
            M³
            3
            25
            Working environment temperature
            Min.20℃,max +45
            26
            Working environment humidity
            --- 
            <60%
            27
            Power supply
            --- 
            380VAC, 3P+N+PE, 50/60Hz
             
            7.PAYMENT TERM
            The contract value shall be paid by the buyer to the seller in the following ways:
            1. 30% of total value will be paid by T/T as down payment.
            2. 70% of total value shall be paid by T/T or L/C before shipment
             
            8. Service terms
            8.1 Service before sale:
            Provide relative technical data for customer choosing equipments. Design floor plan, basic general drawing and quotation.
            8.2 Service in sale
            After the contract working, we will execute each item and keep relevant standards strickly in every manufacturing process. Keep in touch with customer and make sure that craft, quality and technology could meet the requirements.
            8.3 Service after sale:
            Help customer for installation and training at site. Maintenance and repair for one year. Customer should pay for the round-trip flight ticket and accommodation.
            9Quotation Validity 
            Our quotation will be available in 30 days after we send it you by a formal way: fax, email or courier.
            —— 猜你喜歡 ——
            我們熱忱為您服務
            張經理:13961473534
            首頁 | 關于我們 | 產品展示 | 公司新聞 | 常見問題 | 聯系我們 |
            蘇ICP備18029642號-1 常州華陽玻璃設備有限公司 地址:牛塘鎮湖濱北路434號
            電話:0519-83552117 傳真:0519-83552117 張經理:13961473534
            郵箱:86395014@qq.com 網址:http://www.zhiboyuanfeng.com
            2020最新午夜福利视频合集